鈑金加工彎曲介紹:
金屬板的彎曲和成型是在彎板機上進行的。將要成型的工件放在彎板機上，用升降杠桿提起制動蹄，將工件滑到合適的位置，然后將制動蹄降低到要成型的工件上，通過對彎板機上的彎曲杠桿施加力，實現金屬的彎曲成型。最小彎曲半徑是成型金屬的延展性和厚度函數。對于鋁板，金屬的彎曲半徑大于板的厚度。彎曲時，由于有一定的回彈，金屬彎曲角度略大于所需角度。金屬板的彎曲是在金屬加工車間進行的。

鈑金加工彎曲的注意事項。
1.啟動前檢查使用的彎曲設備，確認沒有問題后再啟動，以免發生危險。
2.在機床加工過程中，如遇突發情況需立即停止作業，關閉設備開關。
3.每一次關鍵前都要把MS軸歸零，然后等待大約10秒鐘才能開機。
4.鈑金彎曲時，應放置鈑金工件，保持機床手部平衡。
5.鈑金加工人員在工作過程中應采取相應的保護措施，避免受傷。